Designed as an end piece for square furniture legs, these Square Cap Plugs are perfect for adding a clean, finished look to office and patio furniture, appliances, chair glides, exercise equipment, and everything in between.
- Great for home or office use
- Add an effective finishing piece to furniture, appliances, or exercise equipment
- Designed to fit #14-20 gauge tubes
- Ribbed plastic construction promotes secure fit
- Made of high-quality plastic
| Weight | 0.01 kg |
|---|---|
| Dimensions | 0.59 × 2.701 × 3.858 cm |
| Brand | Hillman |
28 reviews for Hillman 2-Pack 3/4-in Black Plastic Table Leg Caps
Add a review
Related products
Chair Leg Tips & Furniture Glides
$4.48
$9.98
$4.98
Chair Leg Tips & Furniture Glides
Style Selections Anti-skid 10-Pack 2-in Black Rubber Leveling Glides
$6.98
Chair Leg Tips & Furniture Glides
$6.88
Anonymous –
Inventory very limited, had to buy these plugs. I really wanted rubber end covers to slide over the ends of chair leg.
Anonymous –
Have to cut off ribs to make them fit. Brown plastic seems too soft for a chair glide.
Anonymous –
This are less than 1 inch.
Anonymous –
These black plastic caps fit perfectly in a metal lamp that was missing caps. They are not going to come out either as they fit snugly and look better than the original caps.
Anonymous –
The actual size of the plastic guide was smaller than measurement on packet. Fill right out of chair leg. Useless.
Anonymous –
Fits perfectly
Anonymous –
The Hillman plastic leg caps are a great fit for metal chair legs. We were able to install the caps on round aluminum chair legs very easily, without tools.
Two issues with the Hillman caps – only two per pack, and price. I have yet to encounter a chair with only two legs, and considering most chairs have four legs, a two pack doesn’t make sense. Price – two pieces of light weight plastic should not cost half as much as these cost.
Overall, great product, great fit, not enough caps per package, very expensive.
Anonymous –
Would like the foot section that is on the floor to be thicker
Anonymous –
I needed a 5/8″ tip, but the Goose Creek store only had 1/2″ and 1″. I was able to use the 1/2″ tips by building them up with masking tape.
Anonymous –
Purchased these to replace feet that came with a brand new piece of furniture. These are, by far, higher quality that the factory part.
Anonymous –
Clarification by Tom on first review is wrong. Face of cap is more like 1” and fits maybe 7/8 I. D. Instead of 1” I.D. tube Tom stated.
Anonymous –
Used these for end caps on some trim pieces we needed to cut off on a rebuild of a pontoon bottom. They worked great and hid the cut aluminum pieces’ ends for a more polished look.
Anonymous –
Sturdy and fit perfectly into the aluminum base on a table I built. They work as expected.
Anonymous –
I used these to cap the ends of of square tubing used to block sliding doors.
Anonymous –
Was exactly what I needed
Anonymous –
Works well to plug the leg tubes on a folding hunting stool.
Anonymous –
These tips do not work with the Steelworks (Hillman) 3/4″ square aluminum tubing, which is also sold at .
Anonymous –
Bought these tips for use on some old metal chairs that I refurbished into small benches. They worked perfectly to replace the old rusted tips and were easy to use just slipping right into the old frames.
Anonymous –
Worked well for project. Difficult to remove from true 1″ square steel once installed
Anonymous –
Product was what I needed. No help in the store. Even from the two who sauntered past me in the aisle.
Anonymous –
These are not true 1” plugs, they are supposed to fill a 1” square hole. They fall through the 1” opening. I will have to go to Metal Mart and get the correct fit.
Anonymous –
I used these as feet for a metal chair to keep it from scratching the wood floors. Worked great!
Anonymous –
Had some square metal tubing with sharp edges. These worked perfect to plug the tube and make it safe.
Anonymous –
Product was as needed. No help in store!
Anonymous –
Exactly as described, fit perfectly, fair price.
Anonymous –
There was nothing to dis-like about this product. It has a specific purpose which it meets adequately
Anonymous –
Fits 1″ OD or 7/8″ ID perfectly. The stool leg pictured is exactly 1″ OD, so the inside is about 7/8″. The cap fit snugly with a light palm tap.
Anonymous –
perfect fit to 3/4″ ID square tubing used for a towel bar project.